An old product is processed by a remanufacturing process, and after strict inspection, it reaches the same quality as a new product, and the price is 10%-15% cheaper than the new product. Are you willing to buy such a product? Different consumers may have different answers.
Change the old concept: remanufacturing does not mean refurbishment, nor is it second-hand. The scene is the final destination of most scrapped motors at present. However, in addition to this, the motor can also be remanufactured to regain new vitality. High-efficiency remanufacturing of motors is to remanufacture low-efficiency motors into high-efficiency motors or system-saving motors suitable for specific loads and working conditions (such as pole-changing motors, variable-frequency motors, permanent magnet motors, etc.) Wait). Because the publicity of remanufacturing is not in place, users often confuse remanufacturing and maintenance. In fact, there is a significant difference between remanufacturing and maintenance: Remanufacturing general process 1 Recovery process According to the survey, different companies use different methods to recycle motors. For example, Wannan Electric Motor provides different quotations for each recycled motor. Generally, experienced engineers go directly to the recycling site to determine the motor according to the motor's service life, degree of wear, failure rate, and which parts need to be replaced. Whether it meets the requirements for remanufacturing, and then gives a quotation for recycling. For example, in Dongguan, Guangdong, the motor is recycled according to the power of the motor, and the recycling price of the motor with different pole numbers is also different. The higher the number of poles, the higher the price. 2 Dismantling and simple visual inspection The motor is disassembled with professional equipment, and a simple visual inspection is performed first. The main purpose is to determine whether the motor has the possibility of remanufacturing and to simply judge which parts need to be replaced, which can be repaired, and which do not need to be remanufactured. Wait. The main components of simple visual inspection include casing and end cover, fan and hood, rotating shaft, etc. 3 Detection Carry out detailed detection on the parts of the motor, and detect various parameters of the motor, so as to provide a basis for formulating a remanufacturing plan. Various parameters include motor center height, iron core outer diameter, frame size, flange code, frame length, iron core length, power, speed or series, average voltage, average current, active power, reactive power, apparent power , power factor, stator copper loss, rotor aluminum loss, additional loss, temperature rise, etc. 4. In the process of formulating a remanufacturing plan and remanufacturing the motor for efficient remanufacturing, there will be targeted measures for different parts according to the inspection results, but in general, part of the stator and rotor need to be replaced, the frame (end cover) ), etc. are generally reserved for use, and all new components such as bearings, fans, hoods, and junction boxes are used (the newly replaced fans and hoods are new designs that are energy-saving and efficient). 1. For the stator part, the stator coil is cured into a whole by dipping the insulating paint and the stator core, which is usually difficult to disassemble. In the previous motor repair, the method of burning the coil was used to remove the insulating paint, which destroyed the quality of the core and caused great environmental pollution. (For remanufacturing, a special machine tool is used to cut the winding ends, which is non-destructive and pollution-free; after cutting the winding ends, hydraulic equipment is used to press out the stator core with coils. After the core is heated, the stator coils are pulled out; the coils are re-wound according to the new scheme. ;After the stator core is cleaned, carry out the off-line wiring and withstand voltage test. After passing the test, enter the VPI dipping tank for dipping, and then enter the oven to dry after dipping. 2. For the rotor part, due to the interference fit between the rotor core and the rotating shaft , In order not to damage the shaft and the iron core, the intermediate frequency eddy current heating equipment is used in the remanufacturing to heat the surface of the motor rotor. According to the different thermal expansion coefficients of the shaft and the rotor iron core, the shaft and the rotor iron core are separated; after the rotating shaft is processed, the intermediate frequency eddy current heater is used for heating The rotor iron core is pressed into the new shaft; after the rotor is pressed, the dynamic balance test is performed on the dynamic balancing machine, and the new bearing is heated by the bearing heater and installed on the rotor. 3. For the frame and end cover parts, the frame and end cover After passing the inspection, use sandblasting equipment to clean the surface and reuse it. 4. For the fan and fan cover, the original parts are scrapped and replaced with high-efficiency fans and fan covers. 5. For the junction box, the junction box cover and the terminal board are scrapped, Replace with new parts. The junction box seat is cleaned and reused, and the junction box is reassembled It is assembled and tested at the factory. What kind of motor can be remanufactured as the object of remanufacturing? In theory, all motors in various industries can be remanufactured. In fact, companies often choose to remanufacture Electric motors need the availability of main components to be more than 50%, because the remanufacturing of motors with low utilization rates requires very high costs, low profit margins, and there is no need for remanufacturing. At present, most of the users are due to the use of electric motors. If the energy efficiency does not meet the national standards or if you want to replace the high-efficiency motor, the motor will be considered for remanufacturing. After remanufacturing by the enterprise, the remanufactured motor will be sold to him at a lower price. The motor can be remanufactured in two cases: One case is that the motor itself meets the requirements of the national energy efficiency standard, and it is recovered at a low price after being scrapped, and most of the parts can be reused. After remanufacturing, the motor product achieves higher efficiency. The other case is low-efficiency elimination The electric motor produced by the company does not meet the national energy efficiency standard, and reaches the national energy efficiency level through remanufacturing. After recycling, some parts and components are used to transform it into a high-efficiency electric motor and sell it to him. About the quality assurance plan Remanufacturing electric motor enterprises for their own remanufacturing The whole motor is guaranteed for the whole set, and the general warranty period is 1 year. Let the "invisible industry" surface in China, the current remanufacturing industry is like a giant whale in deep diving - huge and hidden, it is a truly worthwhile deep dive. The invisible industry of digging. In fact, in industrialized countries, remanufacturing has been formed an important industry. According to data, the output value of the global remanufacturing industry will exceed US$40 trillion in 2022. The remanufacturing industry in my country has only gradually developed in recent years. However, this huge market that exists invisibly is actually facing a lot of difficulties. One of the embarrassments is the huge dislocation between the high-tech production process and high-level quality performance and the traditional cognition of consumers on remanufacturing, resulting in a continued downturn in the recognition of remanufacturing. Coupled with the lack of unified market access standards, some enterprises refurbished old parts as remanufactured products, disrupting the remanufacturing market order. Speeding up the regulation of the market and formulating relevant industry standards will enable the sunrise industry of remanufacturing to win a longer-term future from its inception.






