Research on Brushless DC Motor Speed Control System Based on DSP
Brushless DC motors have attracted the attention of scholars engaged in motor and drive systems since the late 1970s. There are many forms of motor drive control structure. In recent years, foreign scholars have focused on the torque fluctuation of DC motors and their control problems. The digital control circuit with the single chip microcomputer as the core has strong speed control ability, but can only realize the outer ring digital control of the system, and the DSP can realize the full digital control.
TMS320C28x series is TI's latest 32-bit fixed-point DSP chip, which has digital signal processing capability, powerful time management capability and embedded control function, especially suitable for measurement and control of large-scale data processing [1].
In the brushless DC machine speed control system, in order to enable the debugger to know the running information of the system in real time, it is necessary to collect information such as motor speed and armature current in real time, and perform data analysis and processing [2]. The control process is complicated, and the control algorithm has a large amount of calculation. Therefore, the system selects the DSP chip TMS320F2812 with strong data processing capability as the control core, and then combines the MC33035 dedicated control integrated chip to design and manufacture a brushless DC motor governor.
1 system structure
This system is aimed at high-speed brushless DC motor. In principle, the upper limit of the motor speed is not limited. The maximum motor speed used in the experiment is 50,000 rpm and the motor power is 5kw.
The communication and JOG (manual) modes are designed for user-friendly operation during system design. The communication mode allows the user to conveniently operate the motor in front of the computer, set the maximum speed and acceleration of the motor, and display the current actual speed of the motor. When there is no computer, the user can also perform keyboard operation on the motor through JOG mode. Used to set the speed of the motor.
Funding Fund: National Natural Science Foundation of China (70271001)
The brushless DC motor designed and controlled by the system uses the Hall element as a position feedback mechanism to obtain position information and rotational speed from the feedback pulse signal. The control core DSP corrects the control speed according to the actual speed collected, and realizes the closed-loop control of the motor speed of the system. In addition, the system obtains current information from the drive device IGBT of the motor. By combining these three information, the entire motor speed control system works safely, stably and reliably.
2 system hardware design
The connection of the signal lines between the parts is separated by optocoupler, and the two ends of the optocoupler are connected as shown in FIG. The optocoupler used here is the TLP521, which has an isolation voltage of 2500V. In this system, the maximum voltage of the drive part is 300V, and 2500V can ensure the absolute safety of the system. In Figure 3, the optocoupler is connected in a positive logic, that is, input 1, and the output is also 1. In addition to the TLP521, several high-speed optocouplers 6N127 are used at the connection of the communication line.
2.1 Control section
The core part of the control part is TMS320F2812. It is used in the production of an ICETTEK-2812-B board (DSP development board with 2812). In addition to the DSP, there is also a power management chip that converts the external 5V to 3.3V. powered by.
The 2812 collects the speed, current feedback signal and position feedback signal from the motor. The DSP combines these three signals to output the external control signal. The overcurrent signal fed back from the driving part is a 0, 1 signal. The DSP always monitors this signal when it is working. Once it is monitored, it means that the motor is overloaded, and immediately gives a signal to stop the motor from rotating, so as not to damage the motor. And governor.
The speed control signal output by the DSP is a digital quantity. This digital quantity is converted into a voltage quantity by D/A to the MC33035 for speed regulation. The system uses 12-bit serial D/A (TLV5616), followed by a first-stage amplification (LM358), so that the output voltage can be amplified according to the requirements of different motors.
Communication between the TMS320F2812 and the PC is done via the 485 bus. In industrial control, the 485 bus application is very common, the transmission distance is long and the performance is stable, so the system selects the 485 bus for transmission.
2.2 drive part
The control core of the driver part is MC33035, and the driving devices are IR2183 and IRGP50B60PD1. As the control core of the driving part, MC33035 distinguishes the position of the motor rotor according to the position signal fed back by the motor Hall to control the switching of the IGBT.
Although the IGBT has superior on-state characteristics, it is still not easy to turn off the IGBT instantaneously. During debugging, it was found that a little burr when the IGBT was turned off would cause the motor to heat up or even burn out. This requires corresponding measures in the circuit design, such as a resistor connected in the IR2183 output terminal and the IGBT connection; more careful attention should be paid when the PCB layout is routed, and the layout should be symmetrical.
The motor speed is adjusted by the control pin of the MC33035's 11-pin (error signal amplifier non-inverting input) receiving control section. According to this voltage, a pulse width modulation (PWM) signal is internally generated to control three lower side drive outputs. The speed of the motor is adjusted by changing the output pulse width to change the length of the IGBT on-time.
2.3 display part
The main control component of the display part is AT89C51, and the command is transmitted between the display part and the drive part through the serial port of AT89C51 and 2812 (that is, by communication). The 5V power required for the simultaneous display portion is provided by the control section.
Here, the speed is collected by the counting end of the AT89C51 to collect the pulse signal of the Hall output. This signal is converted into a frequency and sent to the seven-segment digital tube display. Here, the AT89C51 functions as a frequency meter.






