Dec 12, 2018 Leave a message

Comparison of performance between stepper motor and AC servo motor

Comparison of performance between stepper motor and AC servo motor

The stepper motor is a discrete motion device that is intrinsically linked to modern digital control technology. In the current domestic digital control system, the application of stepper motors is very extensive. With the advent of all-digital AC servo systems, AC servo motors are increasingly being used in digital control systems. In order to adapt to the development trend of digital control, stepping motor or all-digital AC servo motor is mostly used as the execution motor in the motion control system. Although the two are similar in control mode (burst and direction signals), there are large differences in performance and application. Now compare the performance of the two.

First, the control accuracy is different

The two-phase hybrid stepping motor step angle is generally 3.6 °, 1.8 °, and the five-phase hybrid stepping motor step angle is generally 0.72 °, 0.36 °. There are also some high-performance stepping motors with smaller step angles, such as a stepper motor for slow wire-cutting machines produced by Beijing Helix Motor Technology Co., Ltd. (formerly Sitong Motor) with a step angle of 0.09. °; three-phase hybrid stepping motor with step angle can be set to 0.9 °, 0.72 °, 0.36 °, 0.18 °, 0.09 °, 0.072 °, 0.036 °, etc. by dial switch, compatible with two-phase and five-phase The step angle of a hybrid stepper motor.

The control accuracy of the AC servo motor is guaranteed by the rotary encoder at the rear of the motor shaft. Taking an imported brand motor as an example, a motor with a standard 2500 line encoder has a pulse equivalent of 360°/10000=0.036° due to the internal quadruple frequency technology of the driver; and for a motor with a 17-bit encoder. The driver receives one 217=131072 pulse motor for one revolution, that is, its pulse equivalent is 360°/131072=9.89 seconds. It is 1/655 of the pulse equivalent of a stepping motor with a step angle of 1.8°.

Second, the low frequency characteristics are different

Stepper motors are prone to low frequency vibration at low speeds. The vibration frequency is related to the load condition and the performance of the driver. It is generally considered that the vibration frequency is half of the take-off frequency of the motor no-load. This low frequency vibration phenomenon, which is determined by the working principle of the stepper motor, is very detrimental to the normal operation of the machine. When the stepper motor works at low speed, damping technology should generally be used to overcome the low frequency vibration phenomenon, such as adding a damper to the motor or using subdivision technology on the drive.

The AC servo motor runs very smoothly, and vibration does not occur even at low speeds. The AC servo system has a resonance suppression function, which can cover the rigidity of the machine, and has a frequency analysis function (FFT) inside the system, which can detect the resonance point of the machine and facilitate system adjustment.

Third, the difference in frequency characteristics

The output torque of the stepping motor decreases as the speed increases, and it drops sharply at higher speeds, so the maximum operating speed is generally 300-600 RPM. The AC servo motor is a constant torque output, that is, it can output the rated torque within its rated speed (generally 2000RPM or 3000RPM), and it is a constant power output above the rated speed.

Fourth, the overload capacity is different

Stepper motors generally do not have overload capability. The AC servo motor has a strong overload capability. Take the Senchuang AC servo system as an example, it has speed overload and torque overload capability. Its maximum torque is three times the rated torque and can be used to overcome the moment of inertia of the inertia load at the moment of starting. Because there is no such overload capability in the stepping motor, in order to overcome this moment of inertia during the selection, it is often necessary to select a motor with a large torque, and the machine does not need such a large torque during normal operation, and a torque appears. The phenomenon of waste.

Five, different operating performance

The control of the stepping motor is open-loop control. If the starting frequency is too high or the load is too large, it may be lost or blocked. If the speed is too high during the stop, the overshoot may occur. Therefore, in order to ensure the control accuracy, it should be handled well. The problem of rising and falling speed. The AC servo drive system is closed-loop control. The drive can directly sample the feedback signal of the motor encoder. The internal position loop and speed loop are formed. Generally, the stepless motor is lost or overshooted, and the control performance is more reliable.

Sixth, the speed response performance is different

It takes 200 to 400 milliseconds for the stepper motor to accelerate from standstill to the operating speed (typically several hundred revolutions per minute). The AC servo system has better acceleration performance. Taking a brand 400W AC servo motor as an example, it takes only a few milliseconds to accelerate from standstill to its rated speed of 3000RPM, which can be used in control situations requiring fast start and stop.

In summary, the AC servo system is superior to the stepper motor in many performance aspects. However, in some occasions where the requirements are not high, stepper motors are often used to perform the motor. Therefore, in the design process of the control system, it is necessary to comprehensively consider the control requirements, cost and other factors, and select the appropriate control motor.


Send Inquiry

whatsapp

teams

E-mail

Inquiry